Icynene Insulation Removal & Replacement in Converse: What to Know First
We provide independent Icynene insulation removal and replacement in Converse, typically completing attic jobs in one to two days with same-week scheduling available. Most homeowners receive a written price before we load a single tool into the truck, and that price includes the documented photo record you’ll walk away with. If you’re seeing settled foam, moisture-stained Icynene, or you’re preparing a home sale and need the attic brought up to current code, this page covers what actually happens on a Converse job. Call (830) 420-0953 to get a written estimate, or bring us another contractor’s quote for a free second opinion.
How Icynene Products Fail - and How We Fix Them
- Icynene Classic Max settled below rafter depth. Open-cell foam like Classic Max can shrink 2-3% during cure, and in Converse’s combination of high summer attic heat and spring humidity spikes, we’ve measured settled areas in 12-year-old installs that dropped from original R-19 equivalent to effective R-13. We remove the degraded foam with specialized scraping tools, then replace with fresh Icynene or a hybrid system depending on your budget and code target.
- Icynene MD-R-200 moisture retention in vented attics. This medium-density closed-cell product is rated for direct application to roof decks, but we’ve found it in Converse homes where the original installer skipped the required vapor-profile analysis. When warm interior air hits the foam’s cold side in January, condensation forms behind it. We cut out the water-damaged sections, map the thermal bridge with infrared, then reinstall with proper dew-point management.
- Icynene LD-C-50 overspray onto electrical penetrations. Light-density open-cell foam expands aggressively, and in older Converse ranch homes near Foster Road we’ve pulled foam off recessed can light housings where the original crew didn’t mask properly. That’s a fire code violation. We remove the contaminated foam, verify the fixture is IC-rated or replace the housing, then reapply with proper thermal barriers where required.
- Icynene H2Foam Lite degradation from rodent activity. Converse’s tree canopy and creek corridors draw roof rats, and they tunnel through open-cell foam like it’s cake. We remove the urine-soaked sections (contaminated insulation removal is a separate protocol from standard tear-out), sanitize the substrate, install rodent-proofing at entry points, then replace with fresh material.
- Icynene Water Blown system shrinkage from improper mix ratios. The water-blown open-cell line is sensitive to substrate temperature and humidity at application. We’ve seen jobs where the crew sprayed at 95°F ambient without adjusting the A-side temperature, resulting in a friable, crumbling surface by year five. We scrape to substrate, verify the deck is sound, and reapply with corrected parameters documented in your job record.
Our Icynene Insulation Removal & Replacement Process
- 1
Call and schedule. A live person answers 24/7. We ask about the Icynene product line if you know it, the install year, and what you’re seeing. We schedule a site visit, usually within 48 hours in Converse.
- 2
Site inspection and blower-door test. We pressurize the house to measure air leakage in CFM50 - cubic feet per minute at 50 pascals - before touching anything. Wes Okafor runs this test personally on Icynene removal jobs because the post-repair number proves the envelope tightened.
- 3
Written price and scope. Under Haven Standard Clause 1, you get a flat price, written scope, and written warranty before anyone lifts a tool. No exceptions. If you have another estimate, we’ll read it with you.
- 4
Removal and substrate prep. We use HEPA-contained scraping and vacuum systems. Contaminated foam goes to separate disposal. We photograph every stage; you get the documented photo record.
- 5
Replacement and air sealing. We seal top plates, can lights, and penetrations before any new insulation goes in. Seal the leaks first. Then insulate. The numbers will tell you if it worked.
- 6
Final blower-door test and documentation. We run the pressurization test again, print the before-and-after comparison, and deliver your written warranty and photo record. The 365-Day Done Right Promise applies from that moment.
Before
AfterWhat Icynene Insulation Removal & Replacement Costs in Converse
Most Icynene removal and replacement jobs in Converse run between $2,800 and $6,400 for a typical 1,800-2,400 square foot home. What moves the price:
- Accessibility: Attics with 18-inch clear height cost less than crawl spaces or truss-framed cavities where we work on our backs.
- Contamination level: Standard foam tear-out runs lower than rodent-contaminated insulation removal requiring HEPA containment and sanitization.
- Replacement material: Reinstalling with Icynene open-cell runs higher than a hybrid system using Rockwool or Owens Corning blown-in over sealed top plates.
- Extent of original install: Full attic coverage versus spot repairs around penetrations.
We also service Reflectix radiant barrier systems and can quote hybrid retrofits if you’re open to alternatives. Call (830) 420-0953 for a written price - estimates are free, and we publish the blower-door numbers so you know what you paid for.
Why Converse Homeowners Call Topside Attic Insulation Converse for Icynene Work
We’re an independent Icynene service provider, not a manufacturer affiliate, which means we source replacement foam from Icynene, Demilec, or other suppliers based on what your specific job requires. Since 2016, we’ve sealed and insulated over 9,000 homes, every one with a written price first and a documented record at completion. Our technicians are background-checked and uniformed; you get a named technician and a text when they’re on the way. The 365-Day Done Right Promise is in writing before work starts, not mentioned after something goes wrong. And because we carry Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, there’s no proprietary lock-in forcing a product that doesn’t fit your house.
FAQs
The original Icynene install warranty, typically 10 years on material and workmanship from a certified applicator, doesn’t transfer to modification work by an independent service provider. We document our replacement with photos, material batch numbers, and our own written warranty under the Haven Standard so you have coverage that doesn’t depend on tracking down the original installer. Call (830) 420-0953 and we’ll review what documentation you have.
How long does Icynene removal and replacement take?
Most Converse jobs finish in one to two days: half a day for removal and prep, half a day for replacement, plus cure time before the final blower-door test. Contaminated insulation removal or deck repairs add a day. We schedule so you’re not living around active work overnight.
Can you match my existing Icynene product, or do I have to switch brands?
We can source current Icynene formulations including Classic Max and H2Foam Lite, but we won’t match a discontinued or recalled product line just for brand consistency. If the original install used a density or chemistry that’s since been revised, we’ll explain the thermal-performance difference and quote both Icynene and equivalent alternatives. Bring us your paperwork for a free second opinion.
Is it cheaper to repair damaged Icynene sections or remove and replace everything?
Spot repairs work when damage is isolated to one area, like a single rodent tunnel or a can-light overspray. When we find shrinkage, moisture degradation, or improper original application affecting more than 30% of the attic footprint, full removal and replacement costs less per square foot and performs better thermally. We mark the boundary on your estimate so you see where each approach applies.
Do you offer emergency Icynene removal if there’s active moisture or mold?
We prioritize water-damaged foam jobs within 24 hours because wet Icynene degrades the substrate beneath it. We don’t perform mold remediation ourselves - we partner with certified remediators in Converse when needed - but we can remove the foam, document the exposed conditions with photos, and return for replacement once the moisture source is resolved. Call (830) 420-0953 for same-day assessment.
Written by Wes Okafor, Owner & Lead Insulation Technician, Topside Attic Insulation Converse at Topside Attic Insulation Converse, serving Converse and nearby areas.